Experience Inc. Jobs

Entry Level Production Trainee - Roseburg Studmill

Roseburg , OR

Share

Posted 1 day ago

Apply NowProcessing...

Email Job

Apply NowProcessing...

Email Job

Job Description

Entry Level Production Trainee

Location: Roseburg Studmill

Swing shift position – 5:30pm-4:00am/Monday-Friday

Hours per shift: Employee works 10-hour shifts, with three 10- minute breaks, and a 30- minute unpaid lunch break.

Wage: $20.83 Hour (.30 swing shift differential)/Fulltime and Long-term Opportunity

Additional: Medical, Dental, and Vision Benefits with low monthly premiums, 401K with match, HSA with match, and On Demand Pay.

Various entry level positions trainee will conduct during a 6-8 week training within the Studmill; see below.

Sticker Operator: Communicate with forklift operators to remove full bundles of kiln sticks. Maintain clean and clear work environment. This position can be fast-paced and requires constant attention and awareness of various operations.

Bander/ Endwax: Operate bander consistent with production needs. Inspect loads to make sure that they are fit to ship. Communicate with supervisors about wood quality or any problems or potential problems. Make sure loads are banded and wrote on correctly.

Paperwrap: Wrap, tag, and end seal units of lumber. Identify and indicate species of wood on paper wrap. Use air and manual staplers to attach paper wrap. Communicate with lift operators to remove and fix bad units. Use air sprayer to apply end wax.

Stacker II: Tag and stack units. Remove bad boards and stickers from operations. Fix cross-ups and jam-ups as they occur. Communicate with Lift operators in yard. Keep work area clean and free of trip hazards.

Sawmill Sorter Help: To maintain consistent wood flow from the Edgers to the Stackers. Also responsible for EDC Saw Change mid-shift and at end of shift.

Dispatch: It is the responsibility of the Dispatch Chaser to follow the requirements below to ensure that all tasks are done safely, while maintaining quality and production goals. Keep work area clear of trip hazards and have a clean working environment.

• Monitoring the sticker flow into slings and strapping up full bundles.

• Keeping belts and chains running freely.

• Monitor the flow of stickers into slings, lockout, and lower bundle down to chain to place two straps around the middle of each unit.

• Monitor and keep the sticker magazines full at the wet board stacker

• Monitor the chipper and its conveyors for plug ups or the metal detector needing reset.

• Pick out bad and broken sticks that are to short or split and slide down the chute in the sticker box below.

• Operate the wet board stacker console on the east side of wet board stacker when possible to help Breakdown operator stay caught up.

• Keep walkways and catwalks clean of any debris.

  Bander/ End Wax

  Essential Functions

• Keep lathe placer in full and in operational condition.

• Verify Grade and length for correctness.

• Spray End Wax.

• Paint stencil when needed.

• Change rolls of banding.

• Utilize slack time by cleaning area.

• Keep work area neat, orderly, and clean.

• Clean bander tracks and heads pre-shift. Perform the PM for the machine.

• Keep battens filled for products being ran.

• Break off lathe pieces sticking out from units.

• Fix unit on strapper re-entry and run through strapper.

• Return miss graded boards to the P.E.T. tree.

  Stacker II

  Essential Functions

• Complete daily PM inspection of all machinery in area prior to use. Notify supervisor, and/or maintenance of any issues that cannot be corrected.

• Operator must bend and twist to fix cross ups on chain and at the hoist.

• Maintain proper sticker placement in unit being stacked and refill cartridges when needed.

• Be able to work overtime when needed and come in early to do operator PMs for Stacker.

• Transfer completed units to bander.

• Complete down time report daily.

• Housekeeping – keep work area and walkways clear of obstacles, debris, and lumber.

• Know how to trouble shoot bander and repair as needed and within a reasonable skill level.

• .Monitor loads as they are transferred from the outfeed hoist through the bander, paint booth, and load doubler chain.

• Change banding as needed.

  Sawmill Sorter Help Essential Functions

• Be able to remove boards from chain that weigh 5-20 lbs.

• Monitors wood flow from Edgers through sorter line.

• Singulates lumber on table and throws away any substandard pieces.

• Maintains communication with all stations to ensure proper wood flow occurs.

• .Keeps work area clean and free of debris.

• Housekeeping - cleans up during downtime.

  Dispatch Chaser

  Essential

• Make sure all trip hazards are picked up before operating.

• Check roll cases to make sure they are clear of debris.

• Monitor cants and flitches at the Type-D to make sure they are going to the correct roll cases and that tipples are working correctly.

• Monitor machine center quality and alert proper personnel.

• Communicate with EDC operator if cants or flitches hang up.

• Assist Newnes, Horizontal, Board Edger operators in fixing crossups.

• Work in a safe manner following all lock out procedures.

  Paperwrap

  Essential Functions

• Wrap, tag, and end seal units of lumber.

• Identify and indicate species of wood.

• Use air and manual staplers to attach paper wrap.

• Communicate with lift operators to remove and fix bad units.

• Use air sprayer to apply end wax.

  Non-Essential Functions

  Perform additional duties as assigned by supervisor for production or cross-training purposes.

  Perform cleanup duties as down-time allows.

  Working Environment: (1) Inside 100% average temperature 70 degrees F (2) Outside 0%; extreme low temperature 10 degrees F, extreme high temperature 115 degrees F. Noise or vibration: Machine noise to include machine being operated as well as other machines close by including Forklifts. Hazards: See Job Hazard Analysis. (3) Atmospheric conditions: Fumes: Wood, Dust: Limited, Mist: Water, Odors: Wood particle, Gasses: None, Poor Ventilation: None

  Personal Protective Equipment Required: (1) Eye Protection. (2) Hearing Protection. (3) Rubber or Leather based gloves when handling dry veneer. (4) Approved Footwear.

  Physical Demands: Required to perform a combination of standing, walking, and climbing stairs. Worker will bend, twist, squat, push/pull (back legs) using waist, shoulders, arms, hands, and wrists to manipulate sheets of veneer on line. Worker will have to visually identify defects and grades associated with stud boards.

  Skills: Must have excellent hand eye coordination. Use vision/hearing continuously. Reading and speech required to communicate comprehension of Job Hazard Analysis, machine specific lockout procedures, monthly safety training, etc. Worker generally works alone with little supervision. Operators must be self-directed in identifying and efficiently completing each task. Ability to prioritize, organize and make necessary decisions.

  Safety: (1) Do only maintenance you are trained to do and keep all body parts out of machinery. (2) Always use our 14-step lockout/tagout procedure before doing any maintenance, clearing jams, or getting into machinery for any reason; be aware of stored energy. (3) Always use proper body mechanics (ex: do not over reach, get help as needed to push loads out). (4) Use proper PPE (gloves, eye protection, hearing protection). (5) Be aware of and communicate with your co-worker at all times (ex: forklift driver). (6) Will be required to read and write during

  PHYSICAL CAPABILITIES

  STRENGTH AND PHYSICAL REQUIREMENTS

  Job Title: Entry Level Production Trainee

  Employee Name:

  ENDURANCE Never/Not Required Seldom

  1-5% Occasionally

  6-33% Frequently

  34-66% Continuous

  67-100% Total hours at one time Total hours in a work day

  SITTING X 8-10 8-10

  STANDING X 8-10 8-10

  WALKING X 8-10 8-10

  CHANGE POSITIONS X

  PHYSICAL REQUIREMENTS: (Enter actual maximum weight in pounds in the box)

  LIFTING Never/Not Required Seldom

  1-5% Occasionally

  6-33% Frequently

  34-66% Continuous

  67-100%

  1-10 LBS 10 LBS

  11-20 LBS 20 LBS

  21-50 LBS 50 LBS

  51-75 LBS 75 LBS

  76-100 LBS 100 LBS

  100 LBS >100 LBS

  Maximum weight lifted by worker without assistance: 50 LBS

  If required, lifting over 50 LBS is performed with two or more people and/or lifting devices.

  CARRYING Never/Not Required Seldom

  1-5% Occasionally

  6-33% Frequently

  34-66% Continuous

  67-100%

  1-10 LBS 10 LBS

  11-20 LBS 20 LBS

  21-50 LBS 50 LBS

  51-75 LBS 75 LBS

  76-100 LBS 100 LBS

  100 LBS 100 LBS

  Maximum weight carried by worker without assistance: 50 LBS

  If required, carrying over 50 LBS is performed with two or more people and/or lifting devices.

  PUSHING/PULLING FORCE TO BE EXCERTED Never/Not Required Seldom

  1-5% Occasionally

  6-33% Frequently

  34-66% Continuous

  67-100%

  1-10 LBS 10 LBS

  11-20 LBS 20 LBS

  21-50 LBS 50 LBS

  51-75 LBS 75 LBS

  76-100 LBS 100 LBS

  100 LBS >100 LBS

  Maximum weight of object pushed/pulled by worker: 75 Lbs. Distance: 2’

  Type of surface (i.e. level, carpet, incline): Level surface

  OTHER Never/Not Required Seldom

  1-5% Occasionally

  6-33% Frequently

  34-66% Continuous

  67-100%

  BEND/STOOP X

  TWIST X

  CROUCH/SQUAT X

  KNEEL X

  CRAWL X

  WALK-LEVEL SURFACE X

  WALK-UNEVEN SURFACE V

  CLIMB STEPS X

  CLIMB LADDER X

  WORK AT HEIGHTS X

  REACH AT OR ABOVE SHOULDER X

  USE OF ARMS X

  USE OF WRISTS X

  USE OF HANDS X

  GRASPING/SQUEEZING X

  OPERATE FOOT CONTROLS X

  ENVIRONMENT

  INSIDE: 90%

  OUTSIDE: 10%

  TEMPERATURE EXTREMES: YES

  VIBRATION: YES

  WORKS ON OR AROUND MOVING MACHINARY OR MECHANICAL PARTS: YES

  PERSONAL PROTECTIVE EQUIPMENT

  BOOTS YES HARDHAT NO GLOVES YES EYE PROTECTION YES HEARING PROTECTION YES OTHER?

  The information provided in this job description, including strength and physical requirements, is based on observation of the job and is accurate to the best of my knowledge.

  Entry Level Production Trainee

  Location: Roseburg Studmill

  Swing shift position – 5:30pm-4:00am/Monday-Friday

  Hours per shift: Employee works 10-hour shifts, with three 10- minute breaks, and a 30- minute unpaid lunch break.

  Wage: $20.83 Hour (.30 swing shift differential)/Fulltime and Long-term Opportunity

  Additional: Medical, Dental, and Vision Benefits with low monthly premiums, 401K with match, HSA with match, and On Demand Pay.

  Various entry level positions trainee will conduct during a 6-8 week training within the Studmill; see below.

  Sticker Operator: Communicate with forklift operators to remove full bundles of kiln sticks. Maintain clean and clear work environment. This position can be fast-paced and requires constant attention and awareness of various operations.

  Bander/ Endwax: Operate bander consistent with production needs. Inspect loads to make sure that they are fit to ship. Communicate with supervisors about wood quality or any problems or potential problems. Make sure loads are banded and wrote on correctly.

  Paperwrap: Wrap, tag, and end seal units of lumber. Identify and indicate species of wood on paper wrap. Use air and manual staplers to attach paper wrap. Communicate with lift operators to remove and fix bad units. Use air sprayer to apply end wax.

  Stacker II: Tag and stack units. Remove bad boards and stickers from operations. Fix cross-ups and jam-ups as they occur. Communicate with Lift operators in yard. Keep work area clean and free of trip hazards.

  Sawmill Sorter Help: To maintain consistent wood flow from the Edgers to the Stackers. Also responsible for EDC Saw Change mid-shift and at end of shift.

  Dispatch: It is the responsibility of the Dispatch Chaser to follow the requirements below to ensure that all tasks are done safely, while maintaining quality and production goals. Keep work area clear of trip hazards and have a clean working environment.

  Sticker Operator Essential Functions

• Monitoring the sticker flow into slings and strapping up full bundles.

• Keeping belts and chains running freely.

• Monitor the flow of stickers into slings, lockout, and lower bundle down to chain to place two straps around the middle of each unit.

• Monitor and keep the sticker magazines full at the wet board stacker

• Monitor the chipper and its conveyors for plug ups or the metal detector needing reset.

• Pick out bad and broken sticks that are to short or split and slide down the chute in the sticker box below.

• Operate the wet board stacker console on the east side of wet board stacker when possible to help Breakdown operator stay caught up.

• Keep walkways and catwalks clean of any debris.

  Bander/ End Wax

  Essential Functions

• Keep lathe placer in full and in operational condition.

• Verify Grade and length for correctness.

• Spray End Wax.

• Paint stencil when needed.

• Change rolls of banding.

• Utilize slack time by cleaning area.

• Keep work area neat, orderly, and clean.

• Clean bander tracks and heads pre-shift. Perform the PM for the machine.

• Keep battens filled for products being ran.

• Break off lathe pieces sticking out from units.

• Fix unit on strapper re-entry and run through strapper.

• Return miss graded boards to the P.E.T. tree.

  Stacker II

  Essential Functions

• Complete daily PM inspection of all machinery in area prior to use. Notify supervisor, and/or maintenance of any issues that cannot be corrected.

• Operator must bend and twist to fix cross ups on chain and at the hoist.

• Maintain proper sticker placement in unit being stacked and refill cartridges when needed.

• Be able to work overtime when needed and come in early to do operator PMs for Stacker.

• Transfer completed units to bander.

• Complete down time report daily.

• Housekeeping – keep work area and walkways clear of obstacles, debris, and lumber.

• Know how to trouble shoot bander and repair as needed and within a reasonable skill level.

• .Monitor loads as they are transferred from the outfeed hoist through the bander, paint booth, and load doubler chain.

• Change banding as needed.

  Sawmill Sorter Help Essential Functions

• Be able to remove boards from chain that weigh 5-20 lbs.

• Monitors wood flow from Edgers through sorter line.

• Singulates lumber on table and throws away any substandard pieces.

• Maintains communication with all stations to ensure proper wood flow occurs.

• .Keeps work area clean and free of debris.

• Housekeeping - cleans up during downtime.

  Dispatch Chaser

  Essential

• Make sure all trip hazards are picked up before operating.

• Check roll cases to make sure they are clear of debris.

• Monitor cants and flitches at the Type-D to make sure they are going to the correct roll cases and that tipples are working correctly.

• Monitor machine center quality and alert proper personnel.

• Communicate with EDC operator if cants or flitches hang up.

• Assist Newnes, Horizontal, Board Edger operators in fixing crossups.

• Work in a safe manner following all lock out procedures.

  Paperwrap

  Essential Functions

• Wrap, tag, and end seal units of lumber.

• Identify and indicate species of wood.

• Use air and manual staplers to attach paper wrap.

• Communicate with lift operators to remove and fix bad units.

• Use air sprayer to apply end wax.

  Non-Essential Functions

  Perform additional duties as assigned by supervisor for production or cross-training purposes.

  Perform cleanup duties as down-time allows.

  Working Environment: (1) Inside 100% average temperature 70 degrees F (2) Outside 0%; extreme low temperature 10 degrees F, extreme high temperature 115 degrees F. Noise or vibration: Machine noise to include machine being operated as well as other machines close by including Forklifts. Hazards: See Job Hazard Analysis. (3) Atmospheric conditions: Fumes: Wood, Dust: Limited, Mist: Water, Odors: Wood particle, Gasses: None, Poor Ventilation: None

  Personal Protective Equipment Required: (1) Eye Protection. (2) Hearing Protection. (3) Rubber or Leather based gloves when handling dry veneer. (4) Approved Footwear.

  Physical Demands: Required to perform a combination of standing, walking, and climbing stairs. Worker will bend, twist, squat, push/pull (back legs) using waist, shoulders, arms, hands, and wrists to manipulate sheets of veneer on line. Worker will have to visually identify defects and grades associated with stud boards.

  Skills: Must have excellent hand eye coordination. Use vision/hearing continuously. Reading and speech required to communicate comprehension of Job Hazard Analysis, machine specific lockout procedures, monthly safety training, etc. Worker generally works alone with little supervision. Operators must be self-directed in identifying and efficiently completing each task. Ability to prioritize, organize and make necessary decisions.

  Safety: (1) Do only maintenance you are trained to do and keep all body parts out of machinery. (2) Always use our 14-step lockout/tagout procedure before doing any maintenance, clearing jams, or getting into machinery for any reason; be aware of stored energy. (3) Always use proper body mechanics (ex: do not over reach, get help as needed to push loads out). (4) Use proper PPE (gloves, eye protection, hearing protection). (5) Be aware of and communicate with your co-worker at all times (ex: forklift driver). (6) Will be required to read and write during

  PHYSICAL CAPABILITIES

  STRENGTH AND PHYSICAL REQUIREMENTS

  Job Title: Entry Level Production Trainee

  Employee Name:

  ENDURANCE Never/Not Required Seldom

  1-5% Occasionally

  6-33% Frequently

  34-66% Continuous

  67-100% Total hours at one time Total hours in a work day

  SITTING X 8-10 8-10

  STANDING X 8-10 8-10

  WALKING X 8-10 8-10

  CHANGE POSITIONS X

  PHYSICAL REQUIREMENTS: (Enter actual maximum weight in pounds in the box)

  LIFTING Never/Not Required Seldom

  1-5% Occasionally

  6-33% Frequently

  34-66% Continuous

  67-100%

  1-10 LBS 10 LBS

  11-20 LBS 20 LBS

  21-50 LBS 50 LBS

  51-75 LBS 75 LBS

  76-100 LBS 100 LBS

  100 LBS >100 LBS

  Maximum weight lifted by worker without assistance: 50 LBS

  If required, lifting over 50 LBS is performed with two or more people and/or lifting devices.

  CARRYING Never/Not Required Seldom

  1-5% Occasionally

  6-33% Frequently

  34-66% Continuous

  67-100%

  1-10 LBS 10 LBS

  11-20 LBS 20 LBS

  21-50 LBS 50 LBS

  51-75 LBS 75 LBS

  76-100 LBS 100 LBS

  100 LBS 100 LBS

  Maximum weight carried by worker without assistance: 50 LBS

  If required, carrying over 50 LBS is performed with two or more people and/or lifting devices.

  PUSHING/PULLING FORCE TO BE EXCERTED Never/Not Required Seldom

  1-5% Occasionally

  6-33% Frequently

  34-66% Continuous

  67-100%

  1-10 LBS 10 LBS

  11-20 LBS 20 LBS

  21-50 LBS 50 LBS

  51-75 LBS 75 LBS

  76-100 LBS 100 LBS

  100 LBS >100 LBS

  Maximum weight of object pushed/pulled by worker: 75 Lbs. Distance: 2’

  Type of surface (i.e. level, carpet, incline): Level surface

  OTHER Never/Not Required Seldom

  1-5% Occasionally

  6-33% Frequently

  34-66% Continuous

  67-100%

  BEND/STOOP X

  TWIST X

  CROUCH/SQUAT X

  KNEEL X

  CRAWL X

  WALK-LEVEL SURFACE X

  WALK-UNEVEN SURFACE V

  CLIMB STEPS X

  CLIMB LADDER X

  WORK AT HEIGHTS X

  REACH AT OR ABOVE SHOULDER X

  USE OF ARMS X

  USE OF WRISTS X

  USE OF HANDS X

  GRASPING/SQUEEZING X

  OPERATE FOOT CONTROLS X

  ENVIRONMENT

  INSIDE: 90%

  OUTSIDE: 10%

  TEMPERATURE EXTREMES: YES

  VIBRATION: YES

  WORKS ON OR AROUND MOVING MACHINARY OR MECHANICAL PARTS: YES

  PERSONAL PROTECTIVE EQUIPMENT

  BOOTS YES HARDHAT NO GLOVES YES EYE PROTECTION YES HEARING PROTECTION YES OTHER?

  The information provided in this job description, including strength and physical requirements, is based on observation of the job and is accurate to the best of my knowledge.

  .

  Equal Opportunity Employer. All qualified applicants will receive consideration for employment without regard to race/ethnicity, color, religion, sex, sexual orientation, gender identity, national origin, disability, protected veteran status, age, or any other status protected by law.